Injection and Anchoring
Showing all 9 results
-
Epo Anchor
Read moreEpo Anchor is two-component products based on epoxy resins, selected fine-grain aggregates and special additives. After mixing Epo Anchor (part A) with hardener (part B), a thixotropic mix, easy to apply is obtained. Once prepared, Epo Anchor hardens by chemical reticulation alone in approximately 5 hours without shrinkage. They become compounds with exceptional bonding and mechanical strength. Epo Anchor may also be applied on very damp surfaces as long as there is no standing water. Epo Anchor meet the requirements defined by EN 1504-9 “Products and systems for the protection and repair of concrete structures.
-
Epo Anchor Fast
Read moreEpo Anchor Fast is two-component products based on epoxy resins, selected fine-grain aggregates and special additives. After mixing Epo Anchor Fast (part A) with hardener (part B), a thixotropic mix, easy to apply is obtained. Once prepared, Epo Anchor Fast hardens by chemical reticulation alone in approximately 5 hours without shrinkage. They become compounds with exceptional bonding and mechanical strength. Epo Anchor Fast may also be applied on very damp surfaces as long as there is no standing water. Epo Anchor Fast meet the requirements defined by EN 1504-9 “Products and systems for the protection and repair of concrete structures.
-
Epo Anchor Slow
Read moreEpo Anchor Slow is two-component products based on epoxy resins, selected fine-grain aggregates and special additives. After mixing Epo Anchor Slow (part A) with hardener (part B), a thixotropic mix, easy to apply is obtained. Once prepared, Epo Anchor Slow hardens by chemical reticulation alone in approximately 5 hours without shrinkage. They become compounds with exceptional bonding and mechanical strength. Epo Anchor Slow may also be applied on very damp surfaces as long as there is no standing water. Epo Anchor Slow meet the requirements defined by EN 1504-9 “Products and systems for the protection and repair of concrete structures.
-
Epo Grout 3C
Read moreThree-component fluid epoxy mortar for anchorage work
-
Epo Grout 3C Plus
Read moreThree-component free-flowing high-strength rapid hardening epoxy grout applied in layers up to 10 cm thick for anchoring and grouting structures
-
Epo Inject Bar100
Read moreTwo-component fluid epoxy resin for anchoring steel bars
-
Epo Inject HV3
Read moreEpo Inject HV3 is a solvent-free epoxy adhesive consisting of two pre-measured components, component A resin, and component B hardener that have to be mixed before use. Epo Inject HV3 has the liquid consistency that can be applied by brush on both horizontal and vertical surfaces. Epo Inject HV3 polymerizes without shrinkage and, after curing, is waterproof, possesses excellent dielectric properties and high mechanical characteristics in addition to its ability to bond concrete and steel. Epo Inject HV3 meets the requirements defined by EN 1504-9 “Products and systems for the protection and repair of concrete structures.
-
Epo Inject LV1
Read moreEpo Inject LV1 is a solvent-free epoxy adhesive consisting of two pre-measured components, component A resin, and component B hardener that have to be mixed before use. Epo Inject LV1 has the liquid consistency that can be applied by brush on both horizontal and vertical surfaces. Epo Inject LV1 polymerizes without shrinkage and, after curing, is waterproof, possesses excellent dielectric properties and high mechanical characteristics in addition to its ability to bond concrete and steel. Epo Inject LV1 meets the requirements defined by EN 1504-9 “Products and systems for the protection and repair of concrete structures.
-
Epo Inject MV3
Read moreEpo Inject MV3 is a solvent-free epoxy adhesive consisting of two pre-measured components, component A resin, and component B hardener that have to be mixed before use. Epo Inject MV3 has the liquid consistency that can be applied by brush on both horizontal and vertical surfaces. Epo Inject MV3 polymerizes without shrinkage and, after curing, is waterproof, possesses excellent dielectric properties and high mechanical characteristics in addition to its ability to bond concrete and steel. Epo Inject MV3 meets the requirements defined by EN 1504-9 “Products and systems for the protection and repair of concrete structures.
